HSB home  
RoentDek Handels GmbH
Im Vogelshaag 8

D-65779 Kelkheim, Germany

page printed: http://www.roentdek.com//products/electronics

 

RoentDek PRODUCT LIST 

FRONT-END ELECTRONICS FOR ANALOG SIGNAL PROCESSING

       
 

Product
number
 

Product
Description
 
 

130

FAMP8c: 8-channel fast timing amplifier unit for detector signals from MCP, delay-line anode or other electron multiplier devices, gain about 70 (adjustable) inverting and non-inverting outputs via lemo 00/250 connectors, 50Ohm impedance. Typical bandwidth 80/200 MHz. 19” rack case with external mains power adapter (100-250VAC). For advanced detector read-out use with standard CFDs or fast ADC systems, e.g. in combination with FT4/12/16-TP.
DESCRIPTION SHEET      MANUAL
 

 

       
  131 FAMP1+: single channel fast timing amplifier unit for amplification of fast detector signals(as from MCP, delay-line anode, channeltron, photo-multiplier, etc.), nominal gain about 70 (adjustable from 0-120%), positive or negative input, bandwidth 200 or 300 MHz, both inverting and non-inverting output via lemo00 connectors. Single box unit incl. mains adapter (100-250V AC).
DESCRIPTION SHEET     MANUAL
       
  134 FAMP3(b): 3-channel fast timing amplifier unit with adjustable gain and reconfigurable bandwidth/input impedance, inverting and non-inverting outputs, 3HU case with external mains adapter (100-250V AC).
DESCRIPTION SHEET     MANUAL

       
  134² FAMP6L: as FAMP3 but with 6 channels (twinFAMP3). Also available as NIM unit FAMP6.
       
       
  136 LET1+: fast leading edge amplifying discriminator for counting, coincidence detection or medium resolution timing tasks. Single box unit incl. mains adapter (100-250V AC). For signals from secondary electron amplifiers such as MCP; PMT or Channeltrons, positive or negative input polarity (please specify). Output NIM or TTL (please specify at time of order)
DESCRIPTION SHEET    MANUAL

       
  164 LA1: 100 MHz (LV)TTL / NIM level signal converter.
DESCRIPTION SHEET   

 
       
  139 ATR19-2b: 2-channel front-end electronics: (amplifier and Constant Fraction discriminator with NIM output (optional ECL) for DLD-detectors in combination with FT4/12/16-TP-type connectors. 3HU case with external mains adapter (100-250V AC). Read-out of a DLD requires two units (one per anode layer) and a FAMP1 + CFD1c (or x) set for the MCP signal.
DESCRIPTION SHEET
 
       
  141 MIXA2: 2-channel analog signal mixing amplifier. Multi-purpose module for signal shaping, mixing and multiplexing. Signal input/output via Lemo connector (50 Ohm). 3HU case with external mains adapter (100-250V AC).Also useful for NIM signals, e.g. as “Fan in”.
DESCRIPTION SHEET 

       
  145 BFAMP3: 3-channel fast timing amplifier unit with adjustable gain and reconfigurable bandwidth/input impedance, inverting and non-inverting bipolar-shaped outputs (shaping delay by cable bridge), 3HU case with external mains adapter (100-250V AC).
DESCRIPTION SHEET
 
       
  146 BFAMP1: as BFAMP3 but with one channel only.  
       
  147 BFAMP8c: as FAMP8c but with bipolar-shaped outputs (like BFAMP1 and BFAMP3)  
       
  148 VL1: active protection amplifier to delimit excessive signal height for subsequent circuits.
DESCRIPTION SHEET
 
       
  150 CFD8c: 8-channel constant fraction discriminator for advanced detector operation in combination with FAMP-type amplifiers. 19" rack case (1HU) with external mains power adapter(100-250VAC). Multi-hit dead-time 10 ns for fast signals (e.g. MCP signal). 300 MHz bandwidth, adjustable threshold, walk, delay, fraction ratio. Analog and digital monitor outputs, gating. NIM (ECL optional) timing outputs with adjustable signal width.
MANUAL
     
  151 CFD4c: constant fraction discriminator like 150, but with 4 channels and a single width NIM unit. Requires a NIM-bin (with +/-6V) or SPS3 for operation, not included.*
MANUAL
       
  384 SPS3: can power up to two CFD4cX
     
  152 CFD1c: single-channel version of CFD8c. 3HU case with external mains adapter (100-250V AC).
MANUAL

     
  154 CFD1x: single-channel CFD incl. pulse-height to NIM pulse-width converter for measuring signal pulse height and signal timing. 3HU case with external mains adapter (100-250V AC).
MANUAL 
     
  155 CFD7x: 7-channel constant fraction discriminator incl. pulse-height to NIM pulse-width converter for one channel (as CFD1x) and 6 channels as in CFD8c, 19" rack case (1HU) as CFD8c.
MANUAL 
     
  159 iUSB-IO2: upgrade option in CFD8c/7x for remote control of threshold settings
     
  170 APG1: test pulser for testing and calibration of electronic modules and delay-line anodes. Provides Nim pulses and attenuated pulses (40 dB) with adjustable repetition rate and width. Single box powered via USB-port (or external +5V source, e.g. battery).
DESCRIPTION SHEET